E-Learning – PLC Siemens S7 300/400

January 27, 2022

E-Learning – PLC Siemens S7 300/400

Jadwal Pelatihan E-Learning – PLC Siemens S7 300/400

TanggalTempatKota
Belum ada jadwal terbaru

Description

  • Be able to recognize S7 hardware and be able to replace modules when a fault occurs
  • Be able to operate the Step 7 software to make it perform certain tasks
  • Understand basic S7 instruction set and be able to make minor modifications to software
  • Be able to backup and restore a PLC program when required
  • Be able to perform basic system diagnostics when a problem occurs

Course Content

1. How Exactly Does a PLC Work?

  • The Led on the output card means i am getting voltage out right? does it?
  • What exactly happens in between? there’s more than just a program in the CPU
  • How exactly does it scan the program?
  • What is this Watchdog Timer? Is it that important?
  • Can I use the same output twice? That’s bad programming isn’t it?
  • A PLC is a logic controller, so use a logical approach to fault find it
  • What are the 8 simple test points to check?
  • The PLC is in RUN, that means there’s a program right? does it?
  • FORCING a bit and toggling a bit is pretty much the same yeah? depends on which PLC

2. How Do I Do The Following?

  • How do I check power is ON and PLC is in right mode (RUN or Program)
  • Check for a fault condition (is SF LED ON)
  • Establish a link to the PLC (accessible nodes)
  • If comms problem check PG/PC interface
  • Create a blank project and take a backup
  • Open project for PLC and go On Line
  • Interrogate Diagnostics Buffer
  • Identify if it is a hardware or software fault?
  • Change the battery
  • Change modules if necessary (with spares and without spares)
  • Identify if it is a PLC or comms fault (Profibus or MPI)
  • Check all settings against a template, Node Address etc
  • Check Hardware Configuration
  • Clear Memory and Download program
  • Check software against latest copy (Compare function)
  • Monitor program
  • Searching for specific operands and instructions
  • Changing timer, counter values On Line
  • Making minor mods Off Line and On Line
  • Check or create a VAT table to establish parameter status
  • Force a parameter if required
  • Call up reference data to assist with software diagnostics
  • Archive and Retrieve project
  • Display Documentation (Symbols, Comments)
  • Reassign an I/O address and change software addresses (Rewire Function)
  • Printing Cross Reference/Program Listings etc

3. Background Information Also Covered

4. Understanding of The Following

  • Number formats, bits, bytes, words, double words
  • Binary, HEX, octal, floating point, integer
  • Data types and parameter types, Bool etc
  • Block types
  • Variable types (local and global)
  • How to monitor various blocks
  • Ladder, STL programs
  • Basic Instructions, contacts, set, reset etc
  • Timers, Counters
  • Comparators, Maths
  • How to make minor mods
  • Altering values in a VAT table
  • Back tracking through a program to establish where power flow stops
  • Overall reset procedure
  • Fault finding tips

5. Course Equipment Per Delegate

  • S7 300 or 400 PLC
  • PC or Laptop
  • Simulator

Form Registrasi Pelatihan / Training

Jika anda berkeinginan untuk mengikuti Pelatihan E-Learning – PLC Siemens S7 300/400, anda bisa langsung menghubungi salah satu nomor kami di bawah ini:

  • (0274) 4291-355 (08:00 – 16:00)
  • 0811 2938 847

Anda juga bisa langsung mengisi Formulir pendaftaran di bawah ini:

E-Learning – PLC Siemens S7 300/400
Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
error: Content is protected !!